View LQ035Q7DB0_187210.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TECHNICAL LITERATURE
(R)
Liquid Crystal Display Group
LQ035Q7DB02
TFT LCD Module
(Model No.: LQ035Q7DB02)
Spec No.: LCY-0204 Issue Date: March 14, 2002
No. DATE
LCY - 02024
MAR. 14. 2002
TECHNICAL
LITERATURE
FOR
TFT - LCD module
MODEL No.
LQ035Q7
B02
TENTATIVE
The technical literature is subject to change without notice. So , please contact Sharp or its representative before designing your product based on this literature.
SHARP CORPORATION MOBILE LIQUID CRYSTAL DISPLAY GROUP
sharp
NOTICE This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. manufacturing processes. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for use in general electronic equipment designs, such as: Personal computers Office automation Telecommunication equipment Industrial control Consumer electronics Test and measurement equipment Audio visual and multimedia equipment SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device
The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: Transportation control and safety equipment(i.e., aircraft, trains, automobiles, etc.) Traffic signals Alarm equipment Gas leakage sensor breakers Various safety devices etc.
SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: Military and space applications Medical equipment for life support Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. Nuclear power control equipment
sharp
(1) Application This literature applies to LQ035Q7DB02. (2) Overview This module is a color reflective and active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor), named AD-TFT(Advanced TFT). It is composed of a color TFT-LCD panel, driver ICs, an FPC, a back light, a touch panel and a back sealed casing. It isn't composed control circuit. Graphics and texts can be displayed on a 240 3 320 dots panel with 262,144 colors by supplying. Optimum view angle is 6 o'clock. An inverted display mode is selective in the vertical or the horizontal direction. 3 Mechanical specifications Table 1 Parameter Screen size (Diagonal) Display active area Pixel format Pixel pitch Pixel configuration Unit outline dimension Mass Surface hardness Note 3-1 Excluding protrusion. For detailed measurements and tolerances, please refer to Fig. 1. (4)Pixel configuration Specifications 8.9 [3.52 ] Diagonal 53.64 H 71.52 V 240(H) 320(V) (1 pixel = R+G+B dots) 0.2235 H 65.0(W) 0.2235 V 4.5 (D) mm mm Note3-1 TYP. R,G,B vertical stripe 85.0(H) 50 3H Units cm mm pixels Remarks
(1,1)
(240,1)
RGB Display area
(1,320)
(240,320)
FPC
sharp
(5)Input/Output terminal 5-1)TFT-LCD panel driving section Table2 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 Symbol VDD AGND MOD MOD U/L SPS CLS AGND VEE VEE VCOM VCOM SPL R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 VSHD DGND PS LP DCLK LBR SPR VSHA I I I I I/O I I I/O I I I I I I I I I I I I I I I I I I Power supply of gate driver(low level) Power supply of gate driver(low level) Common electrode driving signal Common electrode driving signal Sampling start signal RED data signal(LSB) RED data signal RED data signal RED data signal RED data signal RED data signal(MSB) GREEN data signal(LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal(MSB) BLUE data signal(LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal(MSB) Power supply of digital Ground(digital) Power save signal Data latch signal of source driver Data sampling clock signal Selection for horizontal scanning direction Sampling start signal Power supply(analog) Note5-3 I I I I I Control signal of gate driver Control signal of gate driver Selection for vertical scanning direction Start signal of gate driver Clock signal of gate driver Note5-1 Note5-1 Note5-2 I/O Description Power supply of gate driver(high level) Remarks
sharp
Pin No. 40 41 42 43 44 45 46 47 48 49 50
Symbol AGND AGND REV COM AGND AGND AGND AGND AGND AGND AGND
I/O
Description
Remarks
I O
reverse control signal Produce REV signal with the amplitude of AGND
VSHA
Ground(Analog) Cautions when you turn on or off the power supply".
Note5-1 See section(7-1)-(A) " U/L Low
Note5-2 Selection for vertical scanning direction Scanning direction (Pixel configuration) Normal scanning ( X , 1 ) ( X , 320 ) High Inverted scanning ( X , 1) ( X , 320) Note5-3 Selection for horizontal scanning direction LBR High Low SPL Input Output SPR Output Input Scanning direction (Pixel configuration) Normal scanning (1,Y) Inverted scanning (1,Y) (240,Y) (240,Y)
5-2)Back light driving section Table3 Pin No. 1 3 4 5 Symbol VL1 N.C N.C VL2 N.C I Power supply for LED (Low voltage) I/O I Description Power supply for LED (High voltage) Remark
5-3)Touch panel driving section Table 4 Pin No. T1 T2 T3 T4 Symbol YU XR YL XL I/O Description Lower electrode Y (12 o'clock side) upper electrode X (right side) Lower electrode Y (6 o'clock side) upper electrode X (left side) Remark
sharp
(6)Absolute Maximum Ratings Table 5 Parameter Power supply(source/Analog) Power supply(source/Digital) Power supply (gate) Power supply (gate) Input voltage (Digital) Operating temperature (panel surface Storage temperature stg -25 70 Note6-2 [Terminal ] MOD,U/L,SPS,CLS,SPL,R0 R5,G0 G5,B0 B5,LP,DCLK,LBR,SPR,PS,REV Note6-2 Humidity: 95%RH Max.(at Ta 40 ). Maximum wet-bulb temperature is less than 39 (at Ta > 40 ). Condensation of dew must be avoided. Symbol VSHA VSHD VDD VDD-VEE VID opp Condition Ta=25 Ta=25 Ta=25 Ta=25 Ta=25 Ratings -0.3 +7.0 -0.3 +7.0 -0.3 +35.0 -0.3 +35.0 -0.3 VSHD+0.3 0 50 Unit V V V V V [Terminal ] Note6 Remark
sharp
(7)Electrical characteristics 7-1)Recommended operating conditions A) TFT-LCD panel driving section Table 6 Parameter Supply voltage for source driver (Analog) Supply voltage for source driver (Digital) Supply voltage for gate driver High voltage Low voltage Input voltage for Source driver (Low) Input voltage for Source driver (High) Input current for Source driver (Low) Input current for Source driver (High) Input voltage for Gate driver (Low) Input voltage for Gate driver (High) Input current for Gate driver (Low) Input current for Gate driver (High) Common electrode AC component driving signal DC component Symbol VSHA VSHD VDD VEE VILS VIHS IILS IIHS1 IIHS2 VILG VIHG IILG IIHG VCOMAC VCOMDC Min. +4.5 +3.0 +14.5 (-10.5) GND 0.8VSHD GND 0.8VSHD +0.1 Typ. +5.0 +3.3 +15.0 (-10.0) 2.5 +1.1 Max. +5.5 +3.6 +15.5 (-9.5) 0.2VSHD VSHD 30 30 1200 0.2VSHD VSHD 4 4 2.6 +2.1 Unit V V V V V V A A A V V A A Vp-p V Note 7-1 Note 7-1 Note 7-1 Note 7-2 Note 7-3 Note 7-4 Note 7-4 Note 7-4 Note 7-4 Note 7-5 Note 7-5 GND=0V Remarks
Cautions when you turn on or off the power supply Turn on or off the power supply with simultaneously or the following sequence. Turn on Turn off VSHD VSHA VDD VEE VEE VSHA VDD VSHD
The input signal of "MOD" Terminals(Pin No.3 and No.4) must be low voltage when turning on the power supply, and it is held until more than double vertical periods after VCC is turned on completely. After then, it must be held high voltage until turning off the power supply.(Connect Pin No.3 and No.4 terminals to the same signal.) Note 7-1 DCLK,SPL,SPR,LBR,LP,PS,REV,R0 R5,G0 G5 and B0 B5 terminals are applied. Note 7-2 DCLK,SPL,SPR,LBR,LP,REV,R0 R5,G0 G5 and B0 B5 terminals are applied. Note 7-3 PS terminal is applied. Note 7-4 MOD,CLS,SPS and U/L terminals are applied. Note 7-5 VCOMAC should be alternated on VCOMDC every 1 horizontal period and 1 vertical period. VCOMDC bias is adjusted so as to minimize flicker or maximum contrast every each module . B) Back light driving section Ta=25 Symbol VL IL WL VL) MIN TYP (21.6) (15) (0.324) MAX (24) (20) Units V A W Note 7-6 Remarks terminal Parameter LED voltage LED current Power consumption
Table 7
Note 7-6 Calculated reference value(IL
sharp
7-2) Timing Characteristics of input signals Table 8 AC Characteristics (1) Parameter Clock frequency of source driver Rising time of clock Falling time of clock Pulse width (High level) Pulse width (Low level) Frequency of start pulse Source driver Setup time of start pulse Hold time of start pulse Pulse width of start pulse Setup time of latch pulse Hold time of latch pulse Pulse width of latch pulse Setup time of PS Hold time of PS Set up time of data Hold time of data Clock frequency Pulse width of clock(Low) Pulse width of clock(High) Rising time of clock Falling time of clock Gate driver Setup time of clock Hold time of clock Frequency of start pulse Setup time of start pulse Hold time of start pulse Rising time of start pulse Falling time of start pulse Vcom Setup time of Vcom Hold time of Vcom SPL="Hi". Symbol fCK Tcr Tcf Tcwh Tcwl fsp Tsusp Thsp Twsp Tsulp Thlp Twlp Tsups Thps Tsud Thd fcls Twlcls Twhcls Trcls Tfcls Tsucls Thcls fsps Tsu Th Trsp Tfsp Tsuvcom Thvcom 3 1 3 0 50 100 300 100 100 86 20 20 60 0 0 15 10 16.5 5 30 100 100 28 (1/fclk)-30 40 40 16.5 15 10 1.5/fCK 28 Min. 4.5 Typ. (VSHA=+5V, VSHD=+3.3V, Ta=25 ) Max. 6.8 20 20 Unit MHz ns ns ns ns kHz ns ns ns ns ns ns s s ns ns kHz s s ns ns s s Hz ns ns ns ns s s Vcom SPS CLS PS R0 R5,G0 G5 ,B0 B5 LP Note 7-7 SPL,SPR DCLK Remark
Note 7-7 There must be only one up-edge of DCLK (includes Tsusp and Thsp time) in the period of
sharp
&%.
.2
52.
4
4
)
)
$
$
%.5
25
8%1/
Fig.(a) Horizontal timing chart
sharp
%.5

525
4
4
)
)
$
$
Fig.(b) Vertical timing chart
sharp
7-3)Power consumption Measurement condition : SPS=60Hz,CLS=15.73kHz,SPL=15.73kHz,DCLK=6.3MHz The term of PS="Lo" in one horizontal period Ta=25 Table 9 Parameter Source current Gate current Analog Digital High Low Sym Conditions MIN ISHA VSHA=+5.0V ISHD VSHD=+3.3V IDD IEE VDD=+15.0V VEE=-10.0V ( when normal scan mode TYP (3.5) (2.0) (0.05) 0.04) ( MAX (6.0) (3.5) (0.10) 0.10) Unit mA mA mA mA Remarks Note 7-8 Note 7-8 Note 7-9 Note 7-9 37 sec(234DCLK)
Note 7-8 Vertical stripe pattern alternating 21 gray scale (GS21) with 42 gray scale (GS42) every 1 dot. Note 7-9 64-Gray-bar vertical pattern (GS0 GS63 for horizontal way)
sharp
( )Input Signals, Basic Display Color and Gray Scale of Each Color Table 10 Colors & Gray scale Gray Scale Black Blue Green Cyan Red Magenta Yellow White Black Gray Scale of red Gray Scale of green Gray Scale of bleu GS0 GS1 Darker GS2 Basic color 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 R0 R1 R2 R3 Data signal R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
Brighter
GS61 GS62
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Red Black
GS63 GS0 GS1
Darker
GS2
Brighter
GS61 GS62
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Green Black
GS63 GS0 GS1
Darker
GS2
Brighter
GS61 GS62
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
1 0 1
0 1 1
1 1 1
1 1 1
1 1 1
1 1 1
Bleu
GS63
0 :Low level voltage
1 :High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen.
sharp
(9)Optical characteristics 9-1)Not driving the Back light condition Table 11 Parameter Viewing angle range Symbol 21,22 11 12 Contrast ratio Response time Rise Fall CRmax r d x y Reflection ratio R =0 =0 =0 CR2 Condition Min (35) (35) (35) 6 (0.26) (0.30) 5 Typ (50) (50) (50) () 30 50 (0.31) (0.35) ( ) Max 60 100 (0.36) (0.40) % [Note 9-5] ms ms [Note 9-4] Ta=25C Unit degree degree degree [Note 9-2,4] [Note 9-3] Remarks [Note 9-1,2]
White chromaticity
* The measuring method of the optical characteristics is shown by the following figure. * A measurement device is Otsuka luminance meter LCD5000.(With the diffusion reflection unit.) Normal line Photodetector (with luminosity correction system) Chemical coated surface (Optical diffusion treatment)
A diffusion beam
A diffusion beam
A beam (through an optical fiber) Touch panel Module
Center of display
Measuring method (a) for optical characteristics
sharp
9-2)Driving the Back light condition Table 12 Parameter Viewing angle range Symbol 21,22 11 12 Contrast ratio Response time Rise Fall Crmax r d x y Brightness Y = 0 = 0 CR2 Condition Min (30) (30) (30) (50) (0.27) (0.29) Typ (40) (40) (40) (80) 30 50 (0.32) (0.34) (50) Max 60 100 (0.37) (0.39) (cd/m2) IL=20mA ms ms Ta=25C Unit degree degree degree [Note 9-2] [Note 9-3] Remarks [Note 9-1,2]
White chromaticity
* The measuring method of the optical characteristics is shown by the following figure. * A measurement device is TOPCON luminance meter BM-5(A).(Viewing cone 1)
Photodetector(including luminosity facter)
Touch panel LCD module
Center
Measuring method (c) for optical characteristics
sharp
[Note 9-1] Viewing angle range is defined as follows.
Normal line
22 11 12 21
o'clock direction
Definition for viewing angle [Note 9-2] Definition of contrast ratio: The contrast ratio is defined as follows: Photodetecter output with all pixels white(GS63) Contrast ratio(CR)= Photodetecter output with all pixels black(GS0) VCOMAC=5.0Vp-p [Note 9-3] Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white".
White
Black
White
100% 90% Photodetecter output (arbitrary unit) 10% 0% r
Time
d
sharp
[Note 9-4] A measurement device is Minolta CM-2002. [Note 9-5] Definition of reflection ratio Reflection ratio =
Light detected level of the reflection by the LCD module Light detected level of the reflection by the standard white board
(10)Touch panel characteristics Table 13 Parameter Input voltage Resistor between terminals(X1-X2) Resistor between terminals(Y1-Y2) Accuracy of detecting dimension Line linearity(X direction) Line linearity(Y direction) Insuration resistance Minimum tension for detecting (11)Display quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standards for TFT-LCD.. (12)Mechanical characteristics 12-1) External appearance See Fig. 1 12-2) FPC (for LCD panel) characteristics (1)Specific connector FH12A-50S-0.5SH(HIROSE) (2) Bending endurance of the bending slits portion No line of the FPC is broken for the bending test (Bending radius=0.6mm and angle=90) in 30 cycles. 12-3) Design guidance for touchpanel(T/P) 12-3-1)Example of housing design (1)If an consumer will put a palm on housing in normal usage, care should be taken as follows. (2)Keep the gap, for example 0.3 to 0.7mm,between bezel edge and T/P surface. The reason is to avoid the bezel edge from contacting T/P surface that may cause a "short" with bottom layer(See Fig.2) (3)Insertion a cushion material is recommended. (4)The cushion material should be limited just on the busbar insulation paste area. If it is over the transparent insulation paste area, a "short" may be occurred. (5)There is one where a resistance film is left in the T/P part of the end of the pole. Design to keep insulation from the perimeter to prevent from mis-operation and so on. 20 0.1 0.79 300 200 Min. Typ. 5.0 480 419 Max. 7.0 900 850 1.0 1.5 1.5 % % % M N at DC25V Unit V Provisional specification Remark
sharp
12-3-2)Mounting on display and housing bezel (1)In all cases, the T/P should be supported from the backside of the glass. (2)Do not to use an adhensive-tape to bond it on the front of T/P and hang it to the housing bezel. (3)Never expand the T/P top layer(PET-film) like a balloon by internal air pressure. The life of the T/P will be extremely short. (4)Top layer, PET, dimension is changing with environmental temperature and humidity. Avoid a stress from housing bezel to top layer, because it may cause "waving". (5)The input to the Touchpanel sometimes distorts touch panel itself. Housing Cushion material (=Gascket Area) PET Film Insulation metal Transparent Insulation Paste Glass Prohibition Area Fig.2 Response Area Electrode Layer
0.3
0.7mm
sharp
(13)Handling Precautions 13-1) Insertion and taking out of FPCs Be sure insert and take out of the FPC into the connector of the set after turning off the power supply on the set side. 13-2) Handling of FPCs The FPC for LCD panel shall be bent only slit portion. The bending slit shall be bent uniformly on the whole slit portion with bending radius larger than 0.6mm ,and only inner side (back side of the module). Don't bend it outer side (display surface side). Don't give the FPCs too large force, for example, hanging the module with holding FPC. 12-3) Installation of the module On mounting the module, be sure to fix the module on the same plane. Taking care not to warp or twist the module. 13-4)Precaution when mounting (1) If water droplets and oil attaches to it for a long time, discoloration and staining occurs. Wipe them off immediately. (2) Glass is used for the TFT-LCD panel. If it is dropped or bumped against a hard object, it may be broken. Handle it with sufficient care. (3)As the CMOS IC is used in this module, pay attention to static electricity when handling it. Take a measure for grounding on the human body. 13-5)Others (1) The liquid-crystal is deteriorated by ultraviolet rays. Do not leave it in direct sunlight and strong ultraviolet rays for many hours. (2) If it is kept at a temperature below the rated storage temperature, it becomes coagulated and the panel may be broken. Also, if it is kept at a temperature above the rated storage temperature, it becomes isotropic liquid and does not return to its original state. Therefore, it is desirable to keep it at room temperature as much as possible. (3) If the LCD breaks, don't put internal liquid crystal into the mouth. When the liquid crystal sticks to the hands, feet and clothes, wash it out immediately. (4) Wipe off water drop or finger grease immediately. Long contact with water may cause discoloration or spots. (5) Observe general precautions for all electronic components. (6) VCOM must be adjusted on condition of your final product. No adjustment causes the deterioration for display quality. (7) Static image should not be displayed more than 5 minutes in order to prevent from occurrence of residual image.
sharp
(14)Reliability Test Conditions for TFT-LCD Module Table 14 No. 1 2 3 4 5 6 7 Test items High temperature storage test Ta=+70 Low temperature storage test Ta=-25 , 95%RH Test conditions 240h 240h 240h 240h 240h 200pF(0 ) 1 time for each terminals 6 ms 3 times for each direction (JIS C0041, A-7 Condition C) 8 Vibration test Frequency range: 10Hz 55Hz Stroke: 1.5 mm X,Y,Z 9 10 Heat shock test Point activation test (Touch panel) Ta=-25 (1h) R8 HS 60. Hitting force :2.4N Hitting speed : 3 times per second 11 Writing friction resistance test Write according to the right illustration in the (Touch panel) under -mentioned Load : 2.4N Speed : 3 strokes per second Stroke : 30mm Frequency : 50000 times Testing apparatus : shown in Fig (I) Motor
Weight 250gf Stroke 30mm
High temperature and high Tp=+40 humidity operating test High test Low temperature operating test Tp=-10 Electro static discharge test Shock tset 200V 980 m/s2, temperature operating Tp=+50
(But no condensation of dew)
X, Y, Z
Sweep: 10Hz 55Hz
2 hours for each direction (total 6 hours) (JIS C0040,A-10 Condition A) +70 (1h) / 5 cycles
Hit it 1,000,000 times with a silicon rubber of
conditions:
Pen : 0.8R Polyacetal stylus
Touch Panel Fig.(I)
sharp
Note Ta = Ambient temperature, Tp = Panel temperature Check items (a)Test No.1 9 In the standard condition, there shall be no practical problems that may affect the display function. (b)Test No.10 No.11 The measurements after the tests are satisfied (10)-Table 13 (Touch panel characteristics) (15) Others 15-1)Indication of lot number The lot number is shown on a label. Attached location is shown in Fig.1 (Outline Dimensions). Indicated contents of the label LQ035Q7DB02 model No. lot No.
15-2) Used Regulation of Chemical Substances Breaking Ozone Stratum Substances with the object of regulating : CFCS, Carbon tetrachloride, Halon 1,1,1-Trichloro ethane (Methyl chloroform) (a) This LCD module, Constructed part and Parts don't contain the above substances. (b) This LCD module, Constructed part and Parts don't contain the above substances in processes of manufacture. 15-3) If some problems arise about mentioned items in this document and other items, the user of the TFT-LCD module and Sharp will cooperate and make efforts to solve the problems with mutual respect and good will. 16)Forwarding form
a) Piling number of cartons : TBD b) Package quality in one cartons : TBD c) Carton size : TBD d) Total mass of 1 carton filled with full modules : TBD Conditions for storage. Environment (1)Temperature (2)Humidity (3)Atmosphere (4)Period : 0 40 : 60%RH or less (at 40 ) No dew condensation at low temperature and high humidity. : Harmful gas, such as acid or alkali which bites electronic components and/or wires, must not be detected. : about 3 months electrostatic charges, please control the room humidity over 50%RH and open the package taking sufficient countermeasures against electrostatic charges, such as earth, etc. (5)Opening of the package : In order to prevent the LCD module from breakdown by
LCY-02024-20
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible, for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 Fast Info: (1) 800-833-9437 www.sharpsma.com
SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com
SINGAPORE
SHARP Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com
TAIWAN
KOREA
SHARP Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328
SHARP Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855
SHARP Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819
CHINA
HONG KONG
SHARP Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp
SHARP-ROXY (Hong Kong) Ltd. 3rd Business Division, 17/F, Admiralty Centre, Tower 1 18 Harcourt Road, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 13B1, Tower C, Electronics Science & Technology Building Shen Nan Zhong Road Shenzhen, P.R. China Phone: (86) 755-3273731 Fax: (86) 755-3273735

▲Up To Search▲

Price & Availability of LQ035Q7DB0

	To Download LQ035Q7DB0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .